Germany Q-Cells Will Be Built In Malaysia, Solar Cell Factory

Germany Q-Cells solar energy company recently announced plans to invest 5 billion ringgit (1.6 billion U.S. dollars) in Malaysia investment in building a new battery-manufacturing plant, the plant will be built in Malaysia, Selangor Science-Based Industrial Park, about 150 hectares of On the land area. The total investment is expected to 5 billion ringgit, a project will employ 800 to 900 participants.

Construction work is expected to be completed early next year, the second quarter of next year is expected to start operation, after the completion of the second phase project will require a total of 1,600 to 1,800 people. The highest overall capacity is expected to reach about 300 MW annually.

Source: 硅业在线 Jun. 4, 2008

Invents a Major Breakthrough in Improving Performance of Photovoltaic Module with Transparent Polymers to Replace Glass

Enerize Corporation of Florida Invents a Major Breakthrough in Improving Performance of Photovoltaic Module with Transparent Polymers to Replace Glass

Newly developed photovoltaic module designs using proprietary polymer protective coating materials to replace conventional glass can increase conversion efficiency by more then 20%, due to high transparency and concentration of incoming light, while providing resistance to degradation by UV and ionizing radiation, lower cost, reduced weight, and improved mechanical strength.

Coral Springs, FL – May 27, 2008. Enerize Corporation has developed a new design for photovoltaic (PV) modules using a proprietary transparent polymer material that substantially outperforms the glass conventionally used as a protective covering. The proprietary polymer material from Enerize is highly transparent, and stable under UV and ionizing radiation exposure.

Conventional glass has several disadvantages as a protective covering for photovoltaic modules. Glass is relatively heavy, brittle and reflective. Light reflected from the glass surfaces (both exterior and interior) does not reach the solar cell underneath, and glass tends to block ultraviolet light, thus reducing the energy that can be obtained from this part of the spectrum. PV modules that use glass comprise a multi-layered structure that is more expensive and complicated to manufacture as compared to the new polymer coated design.

The new highly transparent polymer material can be applied directly to the PV module surface at low temperatures, eliminating the need for the adhesives required with glass and some other polymers. This eliminates the multi-layer structure including the reflective surfaces present with glass. No glass is used with this polymer coating. The polymer can be formed as a flat smooth surface or as a “crinkle coat”. The “crinkle coat” version further enhances photon collection efficiency due to the light concentrating effect of the polymer material and its surface morphology.

In conventional designs using glass, the efficiency of the PV module can be decreased by 7% or more as compared with a PV module without a glass covering. When PV modules are coated with Enerize polymer encapsulation and protective coating materials a unique result is achieved; namely, conversion efficiency is increased as compared with the same PV module having no covering. Compared to PV modules laminated with glass, those coated with Enerize polymer coating materials exhibit an increase in efficiency of as much as 25% or more. For example, as compared to a PV module laminated with glass having an efficiency of 16.45%, a PV module with the same type of solar cells coated with Enerize polymer material has an efficiency of 21.2%.

This increased efficiency is due to several important features including better utilization of light in the shorter (UV) wavelength range of the spectrum, high transparency of the polymeric coating in the UV range compared to that of glass, and the capability to be formed with a relief or “crinkle coat” surface morphology. This surface morphology more efficiently captures photons over a wider angle of incidence. The polymer’s low reflectance as compared to glass, and the elimination of the interior surface interface, both result in reduced photon loss through reflection.

Additional advantages include reduced weight, increased resistance to degradation by UV and ionizing radiation (so-called photon degradation) and high mechanical strength. These polymer coated PV modules are stable under prolonged exposure to high and low temperatures, thermal-cycling, mechanical impact, and high relative humidity. Evaluation of the new Enerize polymer encapsulation materials has been carried out using PV modules that include up to 5 solar cells with a surface area of 72 cm2 each.

Enerize transparent polymer materials and coating technologies can be used to improve conversion efficiencies and overall performance of mono-crystalline, multi-crystalline, amorphous silicon photovoltaic and non-silicon based PV modules such as CIGS (copper indium gallium selenide).

Dr. Elena Shembel, CEO and co-founder of Enerize Corporation, commented, “We believe that these new type PV modules with polymeric materials that can both protect the active solar cell surface and concentrate incoming light represent an important advance in solar energy that can help improve the performance of photovoltaics across the board. This technology is now at the active product development stage, and Enerize Corporation stands ready with the technology and engineering support required to make these new materials available to PV module manufacturers.”

Enerize Corporation provides proprietary technology and technical know-how in solar energy with an intellectual property portfolio that includes several issued and pending patents in areas critical to the advancement of the solar energy industry.

Source: www.enerize.com May 27, 2008